Table of Contents
- Why noise and vibration harm workers
- What do the 2005 regulations require?
- How should employers assess actual exposure?
- Which controls prevent exposure at source?
- How should employers check health and review controls?
- Frequently Asked Questions
Noise and vibration in the workplace can cause permanent harm long before anyone complains. This guide explains the health effects, statutory exposure action and limit values, and employers’ responsibilities for assessing and controlling workplace noise and vibration. It also explores preventative measures, health surveillance and ongoing monitoring to reduce the risk of permanent occupational ill health.
Why noise and vibration harm workers
Noise and vibration often get missed because the damage builds slowly and quietly. Many workers think muffled hearing or tingling fingers are just part of the job. By the time symptoms are obvious, the resulting health problems may already be permanent.
Who may be exposed?
Harmful exposure can occur in manufacturing, construction, engineering, maintenance and similar work. What decides the risk is the task and the actual exposure, not the job title. A warehouse supervisor who spends hours next to a baler may be more exposed than a colleague with a “noisier” job description.
Grinders, drills, breakers, chainsaws, sanders and powered mowers are all power tools that can expose workers to hand-arm vibration. A grounds team using mowers and strimmers across a whole shift may build up significant exposure without realising it.
In its October 2026 noise and vibration campaign, HSE highlighted that an estimated 15,000 workers experience hearing problems caused or made worse by work each year. The same campaign says around one in five workers may be exposed to harmful noise levels. HSE guidance for employers sets out the risk assessments, controls and hearing protection needed to address this.
How noise affects hearing and safety
Excessive noise can cause occupational hearing loss that is permanent, as well as tinnitus, which people experience as ringing or buzzing in the ears. Hearing damage often develops gradually, so a worker may not notice it until it is well established. A single sudden, very loud sound can also damage hearing.
The human impact goes beyond the ears. Hearing loss makes conversations difficult, and tinnitus can disrupt sleep and concentration. Noise also masks speech, alarms and approaching vehicles, which creates an immediate safety risk on busy sites.
How vibration affects hands and backs
Regular exposure to vibration from hand-held, hand-guided or hand-fed equipment can lead to hand-arm vibration syndrome (HAVS), a potentially disabling condition affecting the nerves, blood vessels, muscles and joints of the hands and arms. HAVS can cause tingling, numbness, pain, weaker grip and fingers turning white in the cold. Hand-arm vibration is also associated with carpal tunnel syndrome, and established damage can be irreversible. HSE sets out practical HAVS prevention and employee protection measures.
Whole-body vibration enters through a seat or the feet, usually when people drive vehicles or mobile machinery. Shocks and jolts are associated with back pain, although posture and manual handling can also contribute.
What do the 2005 regulations require?
Two sets of regulations apply to noise and vibration, and they use different measures. Noise is measured in decibels, while vibration is measured as acceleration over a working day. The figures for one should never be used for the other.
The legal duties across the UK
In Great Britain, the Control of Noise at Work Regulations 2005 and the Control of Vibration at Work Regulations 2005 require employers to assess and control each risk. Northern Ireland has its own, separate regulations that correspond to these.
If an exposure limit is exceeded, the employer must bring exposure back below it straight away. They must also investigate why it happened and change their controls so it does not happen again.
Noise action and limit values
Under the workplace noise regulations, thresholds apply to daily or permitted weekly personal exposure. HSE guidance on the legal requirements and noise exposure thresholds sets the lower action value at 80 dB(A) and the upper action value at 85 dB(A). The exposure limit value is 87 dB(A).
Peak noise is a separate measure from average daily exposure. It covers sudden sound pressure, such as from hammering or impact tools, and has its own thresholds.
| Threshold | Daily or weekly exposure | Peak sound pressure | What it triggers |
| Lower exposure action value | 80 dB(A) | 135 dB(C) | Assess risks, provide information, instruction and training, and make hearing protection available on request. |
| Upper exposure action value | 85 dB(A) | 137 dB(C) | Implement a programme of technical and organisational controls to reduce exposure, provide hearing protection where risk remains, and establish mandatory hearing protection zones where applicable. |
| Exposure limit value | 87 dB(A) | 140 dB(C) | Must not be exceeded, taking account of the protection provided by personal hearing protectors. |
You cannot subtract what hearing protectors block when deciding whether an action value has been reached. Properly worn protection may only be taken into account when checking against the exposure limit.
Vibration action and limit values
The vibration legislation and exposure limits set the hand-arm daily exposure action value at 2.5 m/s² A(8). The daily limit value is 5.0 m/s² A(8). For whole-body vibration, the action value is 0.5 m/s² A(8) and the limit is 1.15 m/s² A(8).
A(8) expresses vibration exposure averaged over an eight-hour reference period. Where exposure is likely to reach or exceed an exposure action value, employers must implement a programme of technical and organisational measures to reduce exposure as low as reasonably practicable, unless the risk can be eliminated at source. Exposure below an action value does not remove the employer’s duty to manage vibration risks. Older transitional arrangements for some legacy equipment have expired and no longer give a general exemption.
How should employers assess actual exposure?
A good assessment reflects how people really work: which tools, for how long and in which areas. Estimates based on unrepresentative data or a single measurement may understate or overstate actual exposure. Assessments should reflect normal working conditions, task duration and variations in equipment use.
Identify tasks and everyone affected
A suitable risk assessment identifies the noisy and vibrating tasks, the equipment, exposure levels and durations, and the controls needed. It also considers employees who may be particularly susceptible. Make sure the assessment looks beyond regular machine operators to:
- Maintenance staff: who carry out short but intense tasks on noisy plant.
- Nearby supervisors: who spend long periods close to noisy processes.
- Temporary and agency workers: who may not be included in routine assessments.
- Contractors and mobile employees: whose exposure across different sites adds up.
On shared sites, employers must assess and manage risks to their own employees and others who may be affected by their activities. Employers must also cooperate, coordinate their protective measures and exchange relevant information about workplace risks. Sharing task information, agreeing controls and inducting visiting workers makes that work in practice. Evidence used for contractor accreditation and approval should match the controls actually used on the job.
Estimate personal noise exposure
Daily noise exposure combines noise levels with the time a person spends in each task and area. A reading taken next to the loudest machine does not tell you anyone’s personal exposure. Peak noise needs to be considered separately.
HSE suggests a closer look if people must raise their voices to talk at 2 metres, have muffled hearing after work, or use noisy equipment for more than half an hour a day. Observation, manufacturer information, comparable data and HSE calculators can support an estimate. Competent measurement may be needed if these cannot give a reliable figure. Annual surveys are not a blanket legal requirement.
Combine vibrating-tool exposure
A vibration risk assessment records each tool’s typical vibration magnitude and the worker’s actual trigger time. A construction worker who cuts, drills and breaks material in one shift builds up a combined daily dose. Each tool cannot be treated as a separate exposure.
Manufacturers’ declared vibration levels are a useful starting point. However, attachments, materials, equipment condition, technique and time in use can change the real result. The HSE calculator supports a practical assessment of daily exposure from vibrating tools. It shows the action value as 100 points and the limit as 400 points. These are just another way of expressing the legal values, not extra limits.
Which controls prevent exposure at source?
Employers must eliminate risks from noise and vibration at source so far as reasonably practicable or, where elimination is not possible, reduce those risks to as low a level as reasonably practicable. Controls at source come first, and protective equipment comes last.

Reduce noise before it reaches workers
Hearing protection alone cannot replace reducing noise at source. Quieter machinery, alternative processes, acoustic enclosures, barriers, isolation and silencers are engineering control measures that cut noise before it reaches anyone.
Separating noisy processes protects people working nearby. Maintaining bearings, components and silencers prevents noise that should not be there. A worn bearing that has gone unreported is an avoidable failure.
Choose equipment and maintain routes
Suitable lower-vibration tools, or methods that avoid vibrating equipment altogether, help reduce exposure to hand-arm vibration. A tool with a lower declared figure is not always the better choice, though, if the job takes much longer with it.
Maintaining tools, attachments and cutting equipment, and replacing worn consumables, prevents vibration rising as equipment deteriorates. For vehicles, practical controls include suitable seats and suspension, maintained tyres, repaired potholes, sensible speeds and managed driving time. Our health and safety checklist guide explains how to check equipment while work is happening.
Use working methods and protection carefully
Task rotation, breaks and scheduling can reduce each person’s operating time. Rotation should not simply spread harmful exposure across more workers.
Where hearing protection is needed, it must suit the noise, fit correctly and work with other PPE. Hearing protection should provide sufficient attenuation without unnecessarily restricting communication or the ability to hear warning signals. HSE recommends reducing noise levels at the ear to below 85 dB(A), while avoiding overprotection that reduces levels below 70 dB(A). Gloves keep hands warm and dry, but they are not a control for hand-arm vibration.
How should employers check health and review controls?
Health surveillance picks up early signs of harm, so employers can act before damage becomes permanent. It also tests whether controls are really working.
Arrange appropriate hearing checks
The Noise Regulations require hearing surveillance where the risk assessment shows a health risk. This includes employees likely to be regularly exposed at or above the upper exposure action values, as well as employees who are particularly susceptible to hearing damage at lower exposure levels.
- Early checks: HSE describes hearing checks usually every year for the first two years.
- Later checks: every three years after that, adjusted to the risk and findings.
- Status: these are HSE guidance intervals, not a fixed legal calendar.
Workers should understand the risks, early symptoms, how exposure is reduced and how to wear their protectors correctly. They should also know how to report defects or concerns.
Monitor vibration-related symptoms
Suitable hand-arm vibration surveillance is required where the assessment shows a health risk. Health surveillance should be provided for employees regularly exposed at or above the hand-arm vibration exposure action value, and for employees considered at risk for other reasons, including those with existing vibration-related health conditions.
HSE describes an initial health assessment before exposure starts, followed by annual symptom screening. Anyone who reports symptoms should be referred for a competent occupational health assessment.
Whole-body vibration does not automatically need the same routine screening. Assess the exposure and respond to back-pain reports, without assuming vibration caused every case.
Act on findings and keep controls current
If surveillance finds harm, get medical advice, review controls, consider alternative work and check colleagues with similar exposure, while protecting confidentiality. Under the Reporting of Injuries, Diseases and Dangerous Occurrences Regulations 2013 (RIDDOR), employers must report medically diagnosed cases of HAVS or carpal tunnel syndrome where the relevant occupational exposure criteria are met. For HAVS, this includes regular use of vibrating or percussive tools, or holding materials that vibrate during processing. For carpal tunnel syndrome, this includes regular use of hand-held vibrating or percussive power tools.
Review workplace noise and vibration assessments when work changes. Even where working conditions remain unchanged, HSE recommends checking whether noise and hand-arm vibration risk assessments need reviewing at intervals of no more than approximately two years. Our health and safety compliance consultancy helps you inspect real conditions, assign actions and follow them through.
Frequently Asked Questions
Is a noise survey report enough to count as a noise risk assessment?
No, not on its own. A suitable and sufficient noise risk assessment should identify workers at risk, estimate personal exposure, consider peak noise and particularly susceptible employees, and identify appropriate control measures and health surveillance requirements. It should also include a prioritised action plan with named responsibilities and timescales. HSE found that around 60% of consultant noise reports it examined lacked enough detail, and 70% did not prioritise controls.
Can a site operator make contractors responsible for noise and vibration risks?
Saying a contractor is responsible does not discharge the site operator’s duties. Before work starts, both should share task and equipment information and agree controls such as segregation, timing and hearing-protection zones. Visiting workers should be inducted, and arrangements checked as work changes.
What should a noise risk assessment consider besides sound levels?
It should consider particularly susceptible workers and whether warning signals can still be heard. As far as practicable, it should also cover interactions with vibration and substances harmful to hearing.

